Copilot Fx Brainzilla dual tap tempo lfo with sequencer pedal

Brainzilla this a dual independent tap tempo LFO with a step sequencer. The sequencer can be assigned to sync/change both LFO rates or tap ratios (sync toggles) or not (each one has its own speed/ratio knob). CV output for the sequencer (to control other devices) and CV jacks for LFO A and LFO B.

Toggle for sequence length (3, 4 or 5 steps) and trigger toggle to set if the sequence is always running or it is manually triggered via the middle footswitch, 3 dual color LEDs indicates which step is currently active. Reset footswitch to restart the sequence to step 1 and the middle footswitch also doubles to pause the sequence when the trigger toggle is in auto-advancing mode, CV input sync jack to sync the tap tempo to an external beat or you can tap twice the footswitch to assign the new rate.


Copilot Fx Arrow Airwaves Supreme white noise generator with custom Artwork

Arrow Airwaves supreme with custom twin peaks artwork (by request). The arrow airwaves supreme is an expanded arrow airwaves it has an lfo that modulates the volume of the white noise section and the dry section (so you can create a fade in/out of both signals), a tremolo white noise or lo-fi tremolo of your signal, also it has a bandpass filter to process the white noise (to get the wind type sounds), the lfo is tap tempo and the extra footswitch allows to turn on/off, the bandpass can also be controlled via expression pedal.

Custom Copilot Fx Kinkilin Delay with CV controls

This Kinkilin has EXP/CV control jacks for delay time, feedback, noise, rate, modulation amount and mix, the extra toggles are to assign both the dry and delay voice to the mix cv. In the video demo of it, the ehx 8 steps is feeding a bandwidth that is controlling the feedback and the delay time, while a broadcast is into the mix cv jack. All the cv inputs are independent so you can use only one at a given time, 2 or 3, all of them or none.

Copilot FX Broadcast triple independent out LFO pedal

Another variation of the Broadcast, this one has 3 independent outputs (2 TRS expression outs and 1 CV out, each one has its own range knob), it also comes with Expression/CV input to control the rate/ratio or manually sweep the outs, invert toggle to have the 2 exp out be synced or unsynced. The extra footswitch changes the output from lfo to the exp/cv in for the 2 expression outs, while the cv out has a toggle.

Custom Trek 10 knobber, pulse width fuzz and oscillation machine pedal

copilot fx trek pwm fuzz custom ped

This one was a request by a member of ilovefuzz, it is a super TREK, I like it so much i built 4, if you are interested email me $130 for the trek alone or $180 for the trek/broadcast combo (note that both the trek and broadcast are blems, they both have some slight scratches and were used).

The 10 knobber Trek, it has a dual parallel sound, side A is a hot overdrive/distortion signal so you can add balance/clarity to the overall signal, while side B is a pulse width fuzz, you can mix and match both sides to taste. The pulse width is similar to an square wave fuzz sound, but you can shape the on/off time of the wave via the range knobs, there are 2 range knobs which are linked to the second footswitch, so you can go from 2 sounds on the fly, it also has the gate and tone knob. The second footswitch also allows to activate the oscillation, in this version there is a OSC knob to fine tune the pitch, a 4 way rotary switch (the knob on the side) to turn off the oscillation or using 3 positions to fine tune the osc range (from high pitches to low tumbling pulses), 2 extra toggles one to add modulation to the osc and other to affect it’s tone. The knob on the top is to cut the fuzz signal to recreate some tremfuzz action. The second range knob also sets the amount of modulation to recreate the PWM tones. Expression/CV jack to add the modulation to the pedal.

Custom Copilot Fx Robotum Ring Modulator pedal

copilot fx robotum ring mod pedalAn oscillation connoisseur requested a robotum with the option that the carrier went into low frequencies so it can create trem type tones, along with the high frequency madness for robot-gonk tones. So this was created, the toggle sets the range of carrier frequency, it also has an extra knob to set the frequency, so it can tune it’s frequency in the high range and just move the toggle for another but lower freq range. But it didn’t end there, since he likes so much oscillation, there’s a momentary switch that activates/morph/transform the carrier frequency adding some subtle elements and not so subtle timbres, so if you press fast enough you can get some pseudo square lfo modulation of the carrier, crazy arpegiations or the sounds of cyborg whales.  I did some quick videos (for instagram, sorry for the camera movement).


Custom Copilot FX Broadcast LFO expression pedal splitter

lfo expression pedal

This is a custom version of the Broadcast, there are 3 independent channels, with the option that the output is the internal LFO or external CV input or expression pedal. Outs 1 and 2 have footswitches, while the the out 3 has a toggle to assign the desired output. The rate / tap ratios can be synced and controlled manually via the expression / cv in (has a toggle to disable this option), also the range of the out 1 can be controlled via the exp / cv in. CV out in case you need more outs.

Custom Copilot Fx Broadband expression pedal splitter

expression pedal cv splitter

A pair of custom broadbands, this units allows to control up to 3 expression jacks  / parameter simultaneously and independently, and the range of each can be set by the user via the knobs, it was requested that the first output has an extra toggle for an inverted sweep (change the direction of the sweep based on the input) and have an extra CV out, so from one expression pedal or cv source it could sync up to 6 expression jacks / parameters (connecting both broadbands). With the inverted sweep it could create Fade In / Fade Out from 2 sources or ping pong pan effect.

Custom Copilot Fx Broadcast LFO pedal with external Sync

Tap Tempo LFO with external sync

I got a request to built a broadcast with the option of being able to sync the tap tempo part of the lfo with an external click instead of taping a switch. There’s a jack on tap where a cable is plugged with the click or a metronome, and when the pedal is in tap mode it will sync (and re-sync so it will stay with the beat), when nothing is plugged in the jack there’s a tap switch available. Other stuff was the invert toggle switch, it changes the sweep direction (so when the wave was up it will be down and vice versa), Exp/CV IN for manual sweep and control of the rate/tap ratios and also the range. CV out to expand via the broadband and bandwidth for more options.